BUMPER PULL COMPATIBLE STEEL FRAME KITS

Choose a professionally pre-designed steel framed kit for speed
or design a custom kit to match your personal style.
Got Kits?

"The NIXIE"

"The Nixie" at Home
Manipulate the 3D Model by using your mouse or finger. Once model fully loads, it can be enlarged by clicking on the last icon (“Fullscreen”) on the bottom.
20′
  • Comes with a 25-year warranty Certificate
  • ICC/ IRC Certification
  • Panel assembly guide
  • Final frame drawings
  • Simpson Straps/Plates (as required by project):
    • LTS12 Twist Strap
    • LSTA36 Strap Tie
    • Simpson Flat Plate
    • Simpson Joist Hangers
  • Ridge-Beam Splice Brackets (if needed)
  • Electrical Grommets
  • 12” Extension bit
  • Gloves
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • Simpson HTT4 Hold down brackets (used for mounting the frame to the trailer)
  • 5/8” Nuts, Bolts, Washers, and Lock Washers
  • 5/8” Drill Bit
  • Sill Gasket
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • All tube mainframe
  • Structural fenders
  • Tongue jack
  • Corner jacks
  • Adjustable coupler
  • Safety chains
  • Dot stickers and lighting
  • Brake away kit
  • Belly pan installed
  • 16” OC crossmembers

We currently working on a complete kit that can be dropped shipped, in phases, directly to your location. At this time, total costs involved in the Complete Kit will be estimated on a per build basis. Contact us for your Complete Kit quote.

 

The Complete Kit is the ultimate package designed for the DIY’er in mind. It includes all the parts needed to finish your tiny house build. Each Complete Kit contains all of the Starter Kit components shown to the left, plus:
  • Exterior siding and trim parts
  • Roofing materials
  • Windows, Doors and Door Locks
  • Exterior finishing such as sealants, and painting products
  • All rough-in and finish plumbing parts (Should be installed by a professional)
  • All rough-in and finish electrical parts (Should be installed by a professional)
  • Propane setup – two (2) 30 lb. propane tanks, dual stage valve, propane connect lines, and mounting brackets. Final appliance connections should be completed by a professional with copper and flared fittings and then, tested.  Due to the custom nature of the unit, the propane hard pipe will need to done on-site.
  • Mini split system. Choice of 9K, 12K, and 18K dual zone units. (line sets, communication cable and drain  line will need to be install by a professional as well as the final connections)
  • Interior wall insulation options. Spray foam kit or Roxul R-15 batts.
  • Interior wall surface
  • Interior trim
  • Flooring
  • Kitchen cabinets (with stock layout or materials for construction if it’s a custom layout)
  • Counter tops and choice of sink
  • Appliance Package such as refrigerator, washer/dryer combo unit, on demand propane water heater, choice of propane cooktop/oven, microwave hood vent, and Lunos e2 fresh air exchangers
  • All necessary fasteners
  • Interior finishing products such as paints and stains
  • Safety products such as smoke detector, fire extinguisher and LP/carbon monoxide detector.

"The LITTLE ZEN"

Bryce Langston's Little Zen
Bryce Langston's "The Little Zen"
Accordion Content
Manipulate the 3D Model by using your mouse or finger. Once model fully loads, it can be enlarged by clicking on the last icon (“Fullscreen”) on the bottom.
20′
  • Comes with a 25-year warranty Certificate
  • ICC/ IRC Certification
  • Panel assembly guide
  • Final frame drawings
  • Simpson Straps/Plates (as required by project):
    • LTS12 Twist Strap
    • LSTA36 Strap Tie
    • Simpson Flat Plate
    • Simpson Joist Hangers
  • Ridge-Beam Splice Brackets (if needed)
  • Electrical Grommets
  • 12” Extension bit
  • Gloves
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • Simpson HTT4 Hold down brackets (used for mounting the frame to the trailer)
  • 5/8” Nuts, Bolts, Washers, and Lock Washers
  • 5/8” Drill Bit
  • Sill Gasket
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • All tube mainframe
  • Structural fenders
  • Tongue jack
  • Corner jacks
  • Adjustable coupler
  • Safety chains
  • Dot stickers and lighting
  • Brake away kit
  • Belly pan installed
  • 16” OC crossmembers

We currently working on a complete kit that can be dropped shipped, in phases, directly to your location. At this time, total costs involved in the Complete Kit will be estimated on a per build basis. Contact us for your Complete Kit quote.

 

The Complete Kit is the ultimate package designed for the DIY’er in mind. It includes all the parts needed to finish your tiny house build. Each Complete Kit contains all of the Starter Kit components shown to the left, plus:
  • Exterior siding and trim parts
  • Roofing materials
  • Windows, Doors and Door Locks
  • Exterior finishing such as sealants, and painting products
  • All rough-in and finish plumbing parts (Should be installed by a professional)
  • All rough-in and finish electrical parts (Should be installed by a professional)
  • Propane setup – two (2) 30 lb. propane tanks, dual stage valve, propane connect lines, and mounting brackets. Final appliance connections should be completed by a professional with copper and flared fittings and then, tested.  Due to the custom nature of the unit, the propane hard pipe will need to done on-site.
  • Mini split system. Choice of 9K, 12K, and 18K dual zone units. (line sets, communication cable and drain  line will need to be install by a professional as well as the final connections)
  • Interior wall insulation options. Spray foam kit or Roxul R-15 batts.
  • Interior wall surface
  • Interior trim
  • Flooring
  • Kitchen cabinets (with stock layout or materials for construction if it’s a custom layout)
  • Counter tops and choice of sink
  • Appliance Package such as refrigerator, washer/dryer combo unit, on demand propane water heater, choice of propane cooktop/oven, microwave hood vent, and Lunos e2 fresh air exchangers
  • All necessary fasteners
  • Interior finishing products such as paints and stains
  • Safety products such as smoke detector, fire extinguisher and LP/carbon monoxide detector.

"The Nooga BLue Sky"

The Award Winning "Nooga Blue Sky"
Accordion Content
Manipulate the 3D Model by using your mouse or finger. Once model fully loads, it can be enlarged by clicking on the last icon (“Fullscreen”) on the bottom.
20′
24′
28′
  • Comes with a 25-year warranty Certificate
  • ICC/ IRC Certification
  • Panel assembly guide
  • Final frame drawings
  • Simpson Straps/Plates (as required by project):
    • LTS12 Twist Strap
    • LSTA36 Strap Tie
    • Simpson Flat Plate
    • Simpson Joist Hangers
  • Ridge-Beam Splice Brackets (if needed)
  • Electrical Grommets
  • 12” Extension bit
  • Gloves
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • Simpson HTT4 Hold down brackets (used for mounting the frame to the trailer)
  • 5/8” Nuts, Bolts, Washers, and Lock Washers
  • 5/8” Drill Bit
  • Sill Gasket
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • All tube mainframe
  • Structural fenders
  • Tongue jack
  • Corner jacks
  • Adjustable coupler
  • Safety chains
  • Dot stickers and lighting
  • Brake away kit
  • Belly pan installed
  • 16” OC crossmembers

We currently working on a complete kit that can be dropped shipped, in phases, directly to your location. At this time, total costs involved in the Complete Kit will be estimated on a per build basis. Contact us for your Complete Kit quote.

 

The Complete Kit is the ultimate package designed for the DIY’er in mind. It includes all the parts needed to finish your tiny house build. Each Complete Kit contains all of the Starter Kit components shown to the left, plus:
  • Exterior siding and trim parts
  • Roofing materials
  • Windows, Doors and Door Locks
  • Exterior finishing such as sealants, and painting products
  • All rough-in and finish plumbing parts (Should be installed by a professional)
  • All rough-in and finish electrical parts (Should be installed by a professional)
  • Propane setup – two (2) 30 lb. propane tanks, dual stage valve, propane connect lines, and mounting brackets. Final appliance connections should be completed by a professional with copper and flared fittings and then, tested.  Due to the custom nature of the unit, the propane hard pipe will need to done on-site.
  • Mini split system. Choice of 9K, 12K, and 18K dual zone units. (line sets, communication cable and drain  line will need to be install by a professional as well as the final connections)
  • Interior wall insulation options. Spray foam kit or Roxul R-15 batts.
  • Interior wall surface
  • Interior trim
  • Flooring
  • Kitchen cabinets (with stock layout or materials for construction if it’s a custom layout)
  • Counter tops and choice of sink
  • Appliance Package such as refrigerator, washer/dryer combo unit, on demand propane water heater, choice of propane cooktop/oven, microwave hood vent, and Lunos e2 fresh air exchangers
  • All necessary fasteners
  • Interior finishing products such as paints and stains
  • Safety products such as smoke detector, fire extinguisher and LP/carbon monoxide detector.

"The Jimmy"

"Jimmy" Kit Artist Rendering
Accordion Content
Manipulate the 3D Model by using your mouse or finger. Once model fully loads, it can be enlarged by clicking on the last icon (“Fullscreen”) on the bottom.
20′
24′
28′
  • Comes with a 25-year warranty Certificate
  • ICC/ IRC Certification
  • Panel assembly guide
  • Final frame drawings
  • Simpson Straps/Plates (as required by project):
    • LTS12 Twist Strap
    • LSTA36 Strap Tie
    • Simpson Flat Plate
    • Simpson Joist Hangers
  • Ridge-Beam Splice Brackets (if needed)
  • Electrical Grommets
  • 12” Extension bit
  • Gloves
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • Simpson HTT4 Hold down brackets (used for mounting the frame to the trailer)
  • 5/8” Nuts, Bolts, Washers, and Lock Washers
  • 5/8” Drill Bit
  • Sill Gasket
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • All tube mainframe
  • Structural fenders
  • Tongue jack
  • Corner jacks
  • Adjustable coupler
  • Safety chains
  • Dot stickers and lighting
  • Brake away kit
  • Belly pan installed
  • 16” OC crossmembers

We currently working on a complete kit that can be dropped shipped, in phases, directly to your location. At this time, total costs involved in the Complete Kit will be estimated on a per build basis. Contact us for your Complete Kit quote.

 

The Complete Kit is the ultimate package designed for the DIY’er in mind. It includes all the parts needed to finish your tiny house build. Each Complete Kit contains all of the Starter Kit components shown to the left, plus:
  • Exterior siding and trim parts
  • Roofing materials
  • Windows, Doors and Door Locks
  • Exterior finishing such as sealants, and painting products
  • All rough-in and finish plumbing parts (Should be installed by a professional)
  • All rough-in and finish electrical parts (Should be installed by a professional)
  • Propane setup – two (2) 30 lb. propane tanks, dual stage valve, propane connect lines, and mounting brackets. Final appliance connections should be completed by a professional with copper and flared fittings and then, tested.  Due to the custom nature of the unit, the propane hard pipe will need to done on-site.
  • Mini split system. Choice of 9K, 12K, and 18K dual zone units. (line sets, communication cable and drain  line will need to be install by a professional as well as the final connections)
  • Interior wall insulation options. Spray foam kit or Roxul R-15 batts.
  • Interior wall surface
  • Interior trim
  • Flooring
  • Kitchen cabinets (with stock layout or materials for construction if it’s a custom layout)
  • Counter tops and choice of sink
  • Appliance Package such as refrigerator, washer/dryer combo unit, on demand propane water heater, choice of propane cooktop/oven, microwave hood vent, and Lunos e2 fresh air exchangers
  • All necessary fasteners
  • Interior finishing products such as paints and stains
  • Safety products such as smoke detector, fire extinguisher and LP/carbon monoxide detector.

"THE SPRINGS"

the Springs Finished Model
Customer Completed "The Springs"
Accordion Content
Manipulate the 3D Model by using your mouse or finger. Once model fully loads, it can be enlarged by clicking on the last icon (“Fullscreen”) on the bottom.
20′
Coming Soon
24′
28′
Coming Soon
  • Comes with a 25-year warranty Certificate
  • ICC/ IRC Certification
  • Panel assembly guide
  • Final frame drawings
  • Simpson Straps/Plates (as required by project):
    • LTS12 Twist Strap
    • LSTA36 Strap Tie
    • Simpson Flat Plate
    • Simpson Joist Hangers
  • Ridge-Beam Splice Brackets (if needed)
  • Electrical Grommets
  • 12” Extension bit
  • Gloves
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • Simpson HTT4 Hold down brackets (used for mounting the frame to the trailer)
  • 5/8” Nuts, Bolts, Washers, and Lock Washers
  • 5/8” Drill Bit
  • Sill Gasket
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • All tube mainframe
  • Structural fenders
  • Tongue jack
  • Corner jacks
  • Adjustable coupler
  • Safety chains
  • Dot stickers and lighting
  • Brake away kit
  • Belly pan installed
  • 16” OC crossmembers

We currently working on a complete kit that can be dropped shipped, in phases, directly to your location. At this time, total costs involved in the Complete Kit will be estimated on a per build basis. Contact us for your Complete Kit quote.

 

The Complete Kit is the ultimate package designed for the DIY’er in mind. It includes all the parts needed to finish your tiny house build. Each Complete Kit contains all of the Starter Kit components shown to the left, plus:
  • Exterior siding and trim parts
  • Roofing materials
  • Windows, Doors and Door Locks
  • Exterior finishing such as sealants, and painting products
  • All rough-in and finish plumbing parts (Should be installed by a professional)
  • All rough-in and finish electrical parts (Should be installed by a professional)
  • Propane setup – two (2) 30 lb. propane tanks, dual stage valve, propane connect lines, and mounting brackets. Final appliance connections should be completed by a professional with copper and flared fittings and then, tested.  Due to the custom nature of the unit, the propane hard pipe will need to done on-site.
  • Mini split system. Choice of 9K, 12K, and 18K dual zone units. (line sets, communication cable and drain  line will need to be install by a professional as well as the final connections)
  • Interior wall insulation options. Spray foam kit or Roxul R-15 batts.
  • Interior wall surface
  • Interior trim
  • Flooring
  • Kitchen cabinets (with stock layout or materials for construction if it’s a custom layout)
  • Counter tops and choice of sink
  • Appliance Package such as refrigerator, washer/dryer combo unit, on demand propane water heater, choice of propane cooktop/oven, microwave hood vent, and Lunos e2 fresh air exchangers
  • All necessary fasteners
  • Interior finishing products such as paints and stains
  • Safety products such as smoke detector, fire extinguisher and LP/carbon monoxide detector.

"THE WEDGE"

Client Completed "Wedge" Kit
Accordion Content
Manipulate the 3D Model by using your mouse or finger. Once model fully loads, it can be enlarged by clicking on the last icon (“Fullscreen”) on the bottom.
20′
24′
28′
Coming Soon
  • Comes with a 25-year warranty Certificate
  • ICC/ IRC Certification
  • Panel assembly guide
  • Final frame drawings
  • Simpson Straps/Plates (as required by project):
    • LTS12 Twist Strap
    • LSTA36 Strap Tie
    • Simpson Flat Plate
    • Simpson Joist Hangers
  • Ridge-Beam Splice Brackets (if needed)
  • Electrical Grommets
  • 12” Extension bit
  • Gloves
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • Simpson HTT4 Hold down brackets (used for mounting the frame to the trailer)
  • 5/8” Nuts, Bolts, Washers, and Lock Washers
  • 5/8” Drill Bit
  • Sill Gasket
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • All tube mainframe
  • Structural fenders
  • Tongue jack
  • Corner jacks
  • Adjustable coupler
  • Safety chains
  • Dot stickers and lighting
  • Brake away kit
  • Belly pan installed
  • 16” OC crossmembers

We currently working on a complete kit that can be dropped shipped, in phases, directly to your location. At this time, total costs involved in the Complete Kit will be estimated on a per build basis. Contact us for your Complete Kit quote.

 

The Complete Kit is the ultimate package designed for the DIY’er in mind. It includes all the parts needed to finish your tiny house build. Each Complete Kit contains all of the Starter Kit components shown to the left, plus:
  • Exterior siding and trim parts
  • Roofing materials
  • Windows, Doors and Door Locks
  • Exterior finishing such as sealants, and painting products
  • All rough-in and finish plumbing parts (Should be installed by a professional)
  • All rough-in and finish electrical parts (Should be installed by a professional)
  • Propane setup – two (2) 30 lb. propane tanks, dual stage valve, propane connect lines, and mounting brackets. Final appliance connections should be completed by a professional with copper and flared fittings and then, tested.  Due to the custom nature of the unit, the propane hard pipe will need to done on-site.
  • Mini split system. Choice of 9K, 12K, and 18K dual zone units. (line sets, communication cable and drain  line will need to be install by a professional as well as the final connections)
  • Interior wall insulation options. Spray foam kit or Roxul R-15 batts.
  • Interior wall surface
  • Interior trim
  • Flooring
  • Kitchen cabinets (with stock layout or materials for construction if it’s a custom layout)
  • Counter tops and choice of sink
  • Appliance Package such as refrigerator, washer/dryer combo unit, on demand propane water heater, choice of propane cooktop/oven, microwave hood vent, and Lunos e2 fresh air exchangers
  • All necessary fasteners
  • Interior finishing products such as paints and stains
  • Safety products such as smoke detector, fire extinguisher and LP/carbon monoxide detector.

"THE CHANTEY"

Client Owned "Chantey" Kit at Christmas
Accordion Content
Manipulate the 3D Model by using your mouse or finger. Once model fully loads, it can be enlarged by clicking on the last icon (“Fullscreen”) on the bottom.
20′
24′
28′
Coming Soon
  • Comes with a 25-year warranty Certificate
  • ICC/ IRC Certification
  • Panel assembly guide
  • Final frame drawings
  • Simpson Straps/Plates (as required by project):
    • LTS12 Twist Strap
    • LSTA36 Strap Tie
    • Simpson Flat Plate
    • Simpson Joist Hangers
  • Ridge-Beam Splice Brackets (if needed)
  • Electrical Grommets
  • 12” Extension bit
  • Gloves
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • Simpson HTT4 Hold down brackets (used for mounting the frame to the trailer)
  • 5/8” Nuts, Bolts, Washers, and Lock Washers
  • 5/8” Drill Bit
  • Sill Gasket
  • All Necessary fasteners and bits (ie screws, See Hardware)
  • All tube mainframe
  • Structural fenders
  • Tongue jack
  • Corner jacks
  • Adjustable coupler
  • Safety chains
  • Dot stickers and lighting
  • Brake away kit
  • Belly pan installed
  • 16” OC crossmembers

We currently working on a complete kit that can be dropped shipped, in phases, directly to your location. At this time, total costs involved in the Complete Kit will be estimated on a per build basis. Contact us for your Complete Kit quote.

 

The Complete Kit is the ultimate package designed for the DIY’er in mind. It includes all the parts needed to finish your tiny house build. Each Complete Kit contains all of the Starter Kit components shown to the left, plus:
  • Exterior siding and trim parts
  • Roofing materials
  • Windows, Doors and Door Locks
  • Exterior finishing such as sealants, and painting products
  • All rough-in and finish plumbing parts (Should be installed by a professional)
  • All rough-in and finish electrical parts (Should be installed by a professional)
  • Propane setup – two (2) 30 lb. propane tanks, dual stage valve, propane connect lines, and mounting brackets. Final appliance connections should be completed by a professional with copper and flared fittings and then, tested.  Due to the custom nature of the unit, the propane hard pipe will need to done on-site.
  • Mini split system. Choice of 9K, 12K, and 18K dual zone units. (line sets, communication cable and drain  line will need to be install by a professional as well as the final connections)
  • Interior wall insulation options. Spray foam kit or Roxul R-15 batts.
  • Interior wall surface
  • Interior trim
  • Flooring
  • Kitchen cabinets (with stock layout or materials for construction if it’s a custom layout)
  • Counter tops and choice of sink
  • Appliance Package such as refrigerator, washer/dryer combo unit, on demand propane water heater, choice of propane cooktop/oven, microwave hood vent, and Lunos e2 fresh air exchangers
  • All necessary fasteners
  • Interior finishing products such as paints and stains
  • Safety products such as smoke detector, fire extinguisher and LP/carbon monoxide detector.